IMTMA Training Centre

IMTMA Scheduled Programmes


24
July, 2018

Understanding and implementation of risk assessment through FMEA

24 to 25 July, 2018, BIEC, 10th Mile Tumkur Road, Madavara Post
In today's competitive market environment, the industry has realized the fact that servicing unreliable products is a very costly proposition. To a large extent, reliability is built into the product during the design and development phase.
26
July, 2018

Machining Aerospace Materials - Challenges and Solutions

26 to 27 July, 2018, Bangalore
Aerospace industry is growing at a rapid pace and India is emerging as a preferred hub for aerospace manufacturing. However, machining of aerospace components is quiet challenging as it involves advanced materials like high performance metal alloys & composites.
26
July, 2018

Improving CNC part quality including accuracy of CNC machines

26 to 27 July, 2018, Chinchwad
The quality of every component produced on a CNC machine is highly dependent on the machine's performance. The accuracy of machined components would depend upon inherent accuracy of the machine tool as well as the machining system as whole including process, Tooling, Work holding and Programming.
26
July, 2018

Design of Workholding & Fixturing

26 to 27 July, 2018, IMTMA, 249F, Udyog Vihar Phase-IV, Sector-18, Gurgaon, Haryana
Design of workholding & fixturing is key to effective utilization of machine tools. Basics of fixture design if not implemented correctly results in poor productivity & quality problems.
31
July, 2018

Defects Analysis and Troubleshooting of Injection Moulded Components

31 July to 1 August, 2018, 12/5, D1 block, MIDC Chinchwad
We are said to be living in an era of Plastics since 1974, as the world consumption of plastics from that year onward exceeded that of steel by volume! From household appliances to airplanes, from tooth brushes to telephones, from Computers to cars, everything seems to be made out of plastics these days.
06
August, 2018

Machine Tool Design - Mechanical (Batch 17)

6 August to 29 September, 2018, BIEC, Bengaluru
The course is structured with introduction to Design fundamentals and more focused on machine tool design. A complete design of CNC Turning center will be carried out from concept to finish.
06
August, 2018

Hands-on training in Spindle Assembly & Maintenance

6 to 11 August, 2018, IMTMA, BIEC, 10th Mile, Near Nice road, Madavara Post, Bangalore
Spindle is the most sophisticated member in machine tool and plays a vital role for better performance, higher efficiency and responsible for quality of machined components and overall productivity.
06
August, 2018

Training on Design of Hydraulic System for machineries

6 to 11 August, 2018, BIEC Bangalore
The course is structured with introduction to basics of Hydraulics system to complete design. Design of Hydraulics is key to effective utilization of any Mechanical Application. Hydraulics design if not implemented correctly results in poor performance & quality problems during running. Conceptualization w.r.t the actual requirement in terms of force, speed and safety is very essential during design. Selection of hydraulic elements, sizing of elements, calculations for optimization, design of entire system is very vital in any mechanical industry. Assembly of hydraulic elements, hydraulic plumbing, machine interface and trouble shooting is key requirement. The entire course is designed to ad
07
August, 2018

Effective Maintenance Towards Zero Down Time- Electrical & Electronic Aspects of CNC Machines

7 to 8 August, 2018, 10th Mile,Tumkur Road,Madavara Post, Bangalore 562123
CNC machines are real Mechatronic systems, having electrical and electronic circuits interacting with mechanical actuators / sub systems. Diagnostics and root cause analysis is an important aspect of maintenance, which is most often ignored.
08
August, 2018

Geometric Dimensioning & Tolerancing (GD&T) in Design through Manufacturing

8 to 10 August, 2018, BIEC, 10th Mile Tumkur Road, Madavara Post
Geometric Dimensioning and Tolerancing (GD&T) system eliminates ambiguities in engineering drawings and brings out the designer's intent very clearly. It ensures seamless communication between design, engineering, manufacturing and quality teams across the entire organization enabling them to work in a concurrent engineering environment.
08
August, 2018

Energy Conservation/Energy Saving in Manufacturing

8 August, 2018, Chinchwad
Energy has re-emerged as an issue of national concern as India confronts the challenges of economic recovery, energy affordability, climate change and energy security. The demand for sustainability is growing stronger every day and manufacturers are looking for ways to reduce energy cost.
09
August, 2018

Assembly, Welding and Inspection Fixtures-Design and Manufacturing

9 to 10 August, 2018, 12/5, D1 Block, MIDC Chinchwad, Pune 411019
Fixtures are used in almost all the segments of the engineering industry and are considered to be critical for achieving optimum quality and productivity of various products. Any shortcomings in the design and manufacture of these fixtures have a direct negative impact on the assemblies manufactured.
10
August, 2018

Gear Metrology and Measuring Methods

10 to 11 August, 2018, IMTMA, 249F, Udyog Vihar Phase-IV, Sector-18, Gurgaon, Haryana
Gears and Gear drives are one of the key components of all kinds of vehicles, machine tools, aircrafts, household appliances as well as a broad variety of industrial equipments. Today the designers are facing challenges of demands about increasing lifetime, power transmission and noise emission, whereas the size and weight of gear drives is constantly reduced.
13
August, 2018

Calibration of Dimentional Measuring Instruments and Evaluation of Uncertainty

13 to 14 August, 2018, Bangalore
Obtaining accurate, reliable and traceable measurements is one of the basic requirements in order to achieve required levels of product quality, in any manufacturing activity. No measurement is exact and every measurement is subject to some uncertainty. 'Uncertainty of measurement' is the doubt that exists about the result of any measurement.
13
August, 2018

Finishing School in Production Engineering- 13th Aug to 10th Sep 2018

13 August to 10 September, 2018, IMTMA, BIEC, 10th Mile, Near Nice road, Madavara Post, Bangalore
The Indian manufacturing sector has become major destination for global players not only for their manufacturing activities but also for marketing their latest developments specially in the field of CNC technologies. However, increased use of CNC machines / CNC automation doesn’t result in enhanced productivity directly. Systematic training in best manufacturing practices is highly crucial and well trained manpower can bring in significant improvement in productivity and quality levels thereby increased profitability. Amidst the competitive work environment today, Effective utilisation of resources including CNC machines, tooling, work holding and other accessories is the key to realise ev
16
August, 2018

Induction Hardening and other surface heat treatment processes

16 to 17 August, 2018, BIEC, 10th Mile Tumkur Road, Madavara Post
Most engineering and automotive parts be it drive line or engine or structural members need to have adequate strength and durability to perform their respective functions. At the same time these parts need to be cost effective. To achieve these twin objective the components are subjected to surface strengthening treatments.
20
August, 2018

Advanced CNC Programming for Machining Centres

20 to 23 August, 2018, 12/5, D1 Block, MIDC Chinchwad
CNC Machining Centres form the core of manufacturing operations right from producing auto parts to machine critical aero space components. Its effective application can ensure increased productivity, highest accuracy, rigidity and improved surface finish.
20
August, 2018

Manufacturing Automation using Robots

20 to 21 August, 2018, Bangalore
ROBOTS have been proven to deliver a host of benefits in a wide variety of manufacturing applications. Industries introducing robots to their production processes have typically seen a significant transformation in their productivity and efficiency, with higher levels of output, product quality and flexibility amongst the many other improvements.
21
August, 2018

Heat Treatment Processes in Metalworking

21 to 22 August, 2018, 12/5, D1 Block, MIDC Chinchwad, Pune 411019
Heat Treatment is a core manufacturing process carried out under controlled application of temperature and atmosphere to optimize certain physical and mechanical properties of metals/alloys.
23
August, 2018

Maintenance & Trouble Shooting of presses

23 to 24 August, 2018, Chinchwad
The focal point and workhorse of the sheet metal shop is the press and maintaining a reliable press system is essential to face the fierce competition faced by today's press shops. In metal stamping, everything from poor quality parts to accelerated die wear and damage often is caused by poor maintenance.
28
August, 2018

Selection & Sizing of Electric Motors

28 to 29 August, 2018, 10th Mile,Tumkur Road,Madavara Post, Bangalore 562123
Electric Motors play an important role in Both in Industry and Household. Motor converts electrical energy to Mechanical energy. Motors are used in industry for operating cranes, Blowers, Machines, Machine tools, Compressors, conveyors, Hydraulic & Oil pumps, Robots, Loco engines and host of other equipment.
28
August, 2018

Automation Project Implementation in Manufacturing

28 to 29 August, 2018, 12/5, D1 Block, MIDC Chinchwad
Smart Manufacturing is envisioned as the future of manufacturing. Today, manufacturing is becoming highly automated and IT-enabled or simply put, "Smart". While automation is fairly well established in manufacturing, by linking it with intelligent devices and a strong IT backbone, manufacturing systems are moving towards autonomous systems.
29
August, 2018

IDR Aproach for trouble shooting Sheet Metal Parts

29 to 30 August, 2018, IMTMA, 249F, Udyog Vihar Phase-IV, Sector-18, Gurgaon, Haryana
In a Press Shop, production runs are carried out for stamping a number of sheet metal components. Each component requires a number of Dies running on multiple presses. For each run, Die setups are changed and various parameters are set.
04
September, 2018

Metallurgy for Non Metallurgists

4 to 5 September, 2018, BIEC, 10th Mile Tumkur Road, Madavara Post
Metallurgy is a branch of material science that focus on the physical and chemical behaviour of metallic elements and its alloys. Knowledge of metallurgy is very important for any design and production engineers. Design of any part generally based on Strength, which comes from alloy composition and metallurgical structure.
06
September, 2018

Fundamentals of Advanced Product Quality Planning (APQP) & Implementation of the Production Part Approval Process (PPAP)

6 to 7 September, 2018, Bangalore
New Product Development assumes lot of significance and has become very much essential for sustaining business growth of industries. However often many costly mistakes and time delay happen in new development of Products / Parts as well as processes.
06
September, 2018

Cost & Cycle Time Reduction in CNC Machining

6 to 7 September, 2018, Chennai
In the highly competitive market scenario, customers determine the price of a product and entrepreneurs need to continuously fine tune the costs to realize profits. Machine utilization has a major impact in reducing the manufacturing cost of components.
06
September, 2018

Failure Mode & Effects Analysis (FMEA)

6 to 7 September, 2018, 12/5, D1 Block, MIDC Chinchwad, Pune 411019
In today's competitive market environment, the industry has realized the fact that servicing unreliable products is a very costly proposition. To a large extent, reliability is built into the product during the design and development phase.
10
September, 2018

Design and Processing of Plastic parts

10 to 11 September, 2018, BIEC, 10th Mile Tumkur Road, Madavara Post
We are said to be living in an era of Plastics since 1974, as the world consumption of plastics from that year onward exceeded that of steel by volume! From household appliances to airplanes, from tooth brushes to telephones, from Computers to cars, everything seems to be made out of plastics these days
11
September, 2018

Additive Manufacturing- Metal & Plastics

11 to 12 September, 2018, Chinchwad
Additive manufacturing / 3D Printing throws open newer possibilities for reproducing complex designs in to real objects. Though originally started for prototyping applications, Additive manufacturing has come a long way since then.
18
September, 2018

Manufacturing of Composite Materials

18 to 19 September, 2018, Bangalore
Composites are able to meet diverse design requirements with significant weight savings as well as high strength-to-weight ratio as compared to conventional materials. The volume and number of applications of composite materials have grown steadily, penetrating and conquering new markets relentlessly beyond the aerospace domain.
19
September, 2018

Towards Zero Defects in Welding Technology

19 to 20 September, 2018, IMTMA, 249F, Udyog Vihar Phase-IV, Sector-18, Gurgaon, Haryana
Industry 4.0 is the current trend in manufacturing world over. Welding, being an essential and important part of any sector of economy, it is also getting ‘intelligentised’ by Virtual Reality, Internet of Things, Quantum Computing, Artificial Intelegence, Additive manufacturing, Cobots etc.
21
September, 2018

Inspection of Sheet Metal Formed Components

21 September, 2018, 12/5, D1 Block, MIDC Chinchwad, Pune 411019
Sheet Metal Manufacturing is extensively employed in Automotive & Auto Components, Aerospace, Construction Equipment, Construction Materials, General Engineering Industry, Furniture, Consumer Durables, Electrical- Electronics, Appliances.
21
September, 2018

Cleaning of Machined Components

21 September, 2018, BIEC, 10th Mile Tumkur Road, Madavara Post
Parts cleaning, like most metalworking processes, are experiencing ever tightening specifications. Owing to the constantly increasing requirements in terms of efficiency, quality and environmental protection the cleaning of industrial parts has become absolutely essential in modern manufacturing processes.
25
September, 2018

Geometric Dimensioning & Tolerancing - Advanced

25 to 26 September, 2018, 10th Mile,Tumkur Road,Madavara Post, Bangalore 562123
The Geometric Dimensioning and Tolerancing systems have been getting evolved over the last 20 plus years continuously. Globalization in various streams of engineering has been instrumental in defining the details and implementation.
25
September, 2018

Selection & Application of Tooling for CNC Machining Aplications

25 to 26 September, 2018, Chinchwad
With increasing manufacturing costs and decreasing profit margins, it is extremely important for machine tool users to choose the right type of tooling that will produce accurate parts at lower costs.
27
September, 2018

Manufacturing excellence through SPC and Seven Quality Tools

27 to 28 September, 2018, 12/5, D1 Block, MIDC Chinchwad
Variation in any manufacturing process is inevitable but needs to be controlled. If external or assignable causes of variations are excluded, the natural causes are restricted to a combination of variations due to machines, tools, methods, materials and people who work at the workplace.
27
September, 2018

Implementing Industry 4.0 in Indian Context

27 September, 2018, IMTMA, 249F, Udyog Vihar Phase-IV, Sector-18, Gurgaon, Haryana
Industry 4.0 or “Smart Manufacturing” has become a buzzword in any International Conference and Trade Fair related to Manufacturing in last few years, covering the holistic-automated-integration of machine / process monitoring with production plan, logistics, vendor processes to Business Level ERP for real time communication and control of overall performance. All major economies are pursuing this concept vigorously and soon it could become a standard norm for Industry operation rather than an option.

Get in touch

  Facebook   Twitter   Linkedin   Google Play   Apple Store